CottageCutz Woodlands & Woodland Animals

Hello, everyone!  So glad you stopped by Guneaux Designs.  Today I am a guest designer for the Scrapping Cottage blog.  The project I have created for you features the wonderful stamps and dies from the CottageCutz Woodlands & Woodland Animals, and the dies from the Rustic Sign & Trees.  I had so much fun creating this card, and I hope you enjoy it!

This photo shows the card more  open than the one above.

This photo shows the card at an angle

I love the gorgeous fox images and dies from the CottageCutz Woodland Animal Set; therefore, I had to add three foxes to my card.  The little raccoon is so adorable that I planned to add two but there was not room on the card.  If you have not purchased the set yet, I promise you will have so much fun creating with it and the CttageCutz Woodlands Set.

To create the card, I stamped, colored (with copics), and cut out the images I would use for the project.

After die cutting the elements, I decided I wanted to fussy cut around them, which I did. Then I created a Step Ladder Center Cut Card with white card stock and sponged on it a sky, sun, and grass.  It was then time to load up the card with the critters.  What fun!!

If you would enjoy making a similar card, select the elements you want to showcase and color and die cut them.  Then create the Step Ladder Center Cut Card by following these instructions.

  • Cut a 7″ x 10″ piece of card stock.
  • With the 7″ side at the top of a cutting tool (henceforth, trimmer), move the card stock to the left to the 1-5/8″ mark,

  • Move the cutting blade of your trimmer down to the 1″ mark and lower the cutting arm.

  • Cut the paper from the 1″ mark to the 8-1/2″ mark.

  • Turn the card stock over, (not around or the cut lines will not match), move it to the 1-5/8″ mark on the trimmer, move the cutting blade down to the 1″ mark, and lower the cutting arm.

  • Cut the card stock from the 1″ mark to the 8-1/2″ mark.

  • Remove card stock from the trimmer, and it will look like the following.  (NOTE: There is 1″ from the top of the 7″ side of the card stock to the first cut line, and 1-1/2″ from the cut line to the bottom.)

  • Place the card stock onto a scoring tool with the 10″ side at the top,  Ensure the 7″ side that is to the left on the scoring tool is the one that has cut lines 1″ from the side. Score at the 1″, 2″, and 3″ marks from the first cut line to the second cut line.  Score at the 5″ mark from the top to the bottom of the card stock.  Score at the 7-1/2″ from the first cut line to the second.

  • Now fold the card stock according to the following: a) 1″ score line is a mountain fold, b) 2″ score line is a valley fold, c) 3″ score line is a mountain fold, d) 5″ score line is a mountain fold on the two sides and a valley fold in the center, and e) 7-1/2″ score line is a mountain fold.
  • Decorate the card to your liking.  If desired and to support the elements placed on the back step (mountain fold) cut a 3-11/16″ x 4-7/8″ piece of card stock and attach it to the back step on which you can add your primary feature.  I added this piece to my card.  When the card is closed, this piece matches the two side folds at the top.

I hope you try this card fold and use the CottageCutz dies found at the Scrapping Cottage to showcase.  Have a great day!


COTTAGECUTZ STAMPS AND DIES USED ON THIS PROJECT:

 


Butterfly_1_1God’s Blessings!
Stamping With Guneaux Designs By Beverly Polen
Firm Reliance on Divine Providence!


JOHN 11:25-26

Jesus said to her, “I am the resurrection and the life.  He who believes in me will live, even though he dies; and whoever lives and believes in me will never die.  Do you be believe this?”

Step Ladder Center Cut Card Fold

Have you searched for instructions on how to make a Step Ladder Center Cut Card Fold?  I have searched and searched for a tutorial or video for this card fold, and I have found so many different measurements and names given for the fold.  I do not know what is correct.  However, I wanted to make a card with the fold, thus, I did a lot of guessing.  Here is my creation, and I will share a tutorial below about the card fold.

Step Ladder Center Cut Card

But first, I want to share a little information about the card.  There are three “steps” in the center of the card with each one higher than the other.  The third step in the back is the highest and includes an additional piece of card stock for the main feature of the card.

Step Ladder Center Cut Card Fold

The measurements I used for the card resulted in a 5″ x 7″ card, or an A7 size card.  I want to draw your attention to the third step that I mentioned includes an additional piece of card stock.  Look closely, and you will see an inlaid snowflake in white.  Look even closer and you will see twine behind the snowflake.  This technique is called the Twine Inlay Technique.  Here is a tutorial for this technique.  The following photo is a closeup of the results of using the technique.

I prepared this card for submission to a Splitcoaststampers “Technique Lovers Challenge”, which involved using the Twine Inlay Technique. I created this main feature of the card with the Memory Box Alpine Snowflake Die.

Enjoy the card, and leave a comment about it!


STEP LADDER CENTER CUT CARD FOLD TUTORIAL

  • Cut a 7″ x 10″ piece of card stock,
  • With the 7″ side at the top of a cutting tool (henceforth, trimmer) move the card stock to the left to the 1-5/8″ mark,
  • Move the cutting blade of your trimmer down to the 1″ mark,

  • Cut the card stock from the 1″ mark down to the 8-1/2″ mark,

  • The result is a 7-1/2″ cut,

  • Flip the card stock over, not around, so that the BACK that was face down is now face up (if you turn the card stock around 90 degrees instead, the cuts will not line up),
  • With the 7″ side at the top of the trimmer, move the card stock to the left to the 1-5/8″ mark,

  • Move the cutting blade of your trimmer down to the 1″ mark,

  • Cut the card stock from the 1″ mark down to the 8-1/2″ mark, resulting in the cuts on both sides lining up evenly,

  • Place the card stock onto a scoring tool with the 10″ side at the top and the cuts beginning at the 1″ mark against the left of the tool,

  • Beginning at the 1″ mark and at the first cut line, score down to the second cut line,

  • Score at the 2″ and 3-1/2″ within the two cut lines,

  • Score at the 5″ mark from the top of the card stock to the bottom,

  • Score at the 7-1/2″ mark within the two cut lines,

  • With the card stock cut and scored, begin folding the score lines as shown in this photo,

  • The Step Ladder Center Cut Card Fold will look like the following after folding.

  • With the card stock standing after the folding, it will look like this:

  • Decorate the card as desired.  If a piece of card stock with the main feature is added to the third step of the step ladder card, cut the piece at 3-11/16″ x 4-7/8″ so it will fit horizontally and vertically.   Of course die cuts or other elements can be added on the third step as a main feature.  Enjoy your creation.

Butterfly_1_1God’s Blessings!
Stamping With Guneaux Designs By Beverly Polen
Firm Reliance on Divine Providence!


 1 PETER 3:12-15 (NIV)

“For the eyes of the Lord are on the righteous and his ears are attentive to their prayer, but the face of the Lord is against those who do evil.  Who is going to harm you if you are eager to do good?  But even if you should suffer for what is right, you are blessed. Do not fear what they fear; do not be frightened.  But in your hearts set apart Christ as Lord.  Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have.”